网上有人把它拧花了。最后用六点套筒,加上其它硬件的排列组合,把它成功拧下。
继续。拆engine mount bottom base. 后面沉头的螺栓很难搞。
所有跟帖:
•
Lug Nut拧花了 有什么办法卸下来吗
-落城一哥-
♂
(0 bytes)
()
09/09/2020 postreply
12:29:43
•
用小半号的12角 socket 敲进去
-iGarage-
♂
(0 bytes)
()
09/09/2020 postreply
12:40:36
•
多谢!去试试。还有人有别的法子么
-落城一哥-
♂
(0 bytes)
()
09/09/2020 postreply
12:44:12
•
用impact wrench試試
-violinpiano-
♂
(0 bytes)
()
09/09/2020 postreply
12:52:40
•
也想过去买这种电动的试试,但没有把握
-落城一哥-
♂
(0 bytes)
()
09/09/2020 postreply
13:10:02
•
也想过让修车铺卸下来再换新的
-落城一哥-
♂
(0 bytes)
()
09/09/2020 postreply
13:11:11
•
用bolt extractor
-piper-
♀
(0 bytes)
()
09/09/2020 postreply
13:13:31
•
6角的lug nuts怎么花法?来张图片看看。你的套筒不也是6
-piper-
♀
(0 bytes)
()
09/09/2020 postreply
13:17:34
•
套筒打滑。手头无照
-落城一哥-
♂
(0 bytes)
()
09/09/2020 postreply
13:22:28
•
你换用6边的套筒就行了
-piper-
♀
(0 bytes)
()
09/09/2020 postreply
13:26:08
•
用的就是六边套筒。六角Nuts的角化了
-落城一哥-
♂
(0 bytes)
()
09/09/2020 postreply
13:30:29
•
角花了,是因为你用了12边的套筒,换成6边的就行了
-piper-
♀
(0 bytes)
()
09/09/2020 postreply
14:10:17
•
没有用过12边的。一直用六边的。可能是上的时候用劲过猛
-落城一哥-
♂
(0 bytes)
()
09/09/2020 postreply
14:24:49
•
用6边的花了,这得花多大的力。你可以观察一下套筒里面的形状,
-piper-
♀
(163 bytes)
()
09/09/2020 postreply
15:27:15
•
这个不会错的
-落城一哥-
♂
(0 bytes)
()
09/09/2020 postreply
15:33:53
•
六角花不罕见,Eric的视频里都可看见
-chinomango-
♂
(0 bytes)
()
09/28/2020 postreply
19:11:31
•
lug nut extractor
-biglow-
♂
(0 bytes)
()
09/09/2020 postreply
14:08:13
•
这是其中之一
-落城一哥-
♂
(143 bytes)
()
09/09/2020 postreply
14:23:33
•
那个螺栓的净空很小,我怀疑bolt extractor 能否装的上。最重要的是用六边套筒,套筒完全套入,没有角度。
-indexguy-
♂
(0 bytes)
()
09/09/2020 postreply
15:10:17
•
bolt extractor 和套筒形状是一样的
-piper-
♀
(87 bytes)
()
09/09/2020 postreply
15:29:36
•
看来要买一套。
-indexguy-
♂
(0 bytes)
()
09/09/2020 postreply
17:42:59
•
正时皮带暴露后,顺时针转直到三个点全部对正。
-indexguy-
♂
(163 bytes)
()
09/09/2020 postreply
13:40:21