05 Sienna. 手册要求9万迈换一次。
现在进行式:换正时皮带和水泵。
所有跟帖:
• 拆雨刷,拆cowl panel. -indexguy- ♂ (101 bytes) () 09/09/2020 postreply 05:54:52
• 卸右前轮。拆右侧fender apron. 10mm socket. -indexguy- ♂ (0 bytes) () 09/09/2020 postreply 06:27:28
• 欢迎带图直播。 -ddy- ♂ (0 bytes) () 09/09/2020 postreply 07:05:12
• 油管上有关sienna和Lexus 正时皮带的视频很多,人家那个才是专业的。 -indexguy- ♂ (0 bytes) () 09/09/2020 postreply 10:58:02
• 用Ryobi impact wrench 拆曲轴皮带轮上的螺栓。 -indexguy- ♂ (92 bytes) () 09/09/2020 postreply 07:06:28
• balancer pulley needs mark align? -piper- ♀ (46 bytes) () 09/09/2020 postreply 07:20:35
• 不明白你的问题,拆crankshaft pulley之前,我做了记号。 -indexguy- ♂ (0 bytes) () 09/09/2020 postreply 10:59:55
• 放冷却水。都市传说:若搞不掂crankshaft 螺栓,你就做不下去了。 -indexguy- ♂ (0 bytes) () 09/09/2020 postreply 07:26:23
• impact wrench, 很容易搞定的:) -piper- ♀ (0 bytes) () 09/09/2020 postreply 07:29:16
• 或用丰田的一个小专用工具加break bar 也可以 -majhong- ♂ (0 bytes) () 09/09/2020 postreply 08:06:14
• 那个专门工具只能用于toyota的车,toyota 新车不用正时皮带。所以,决定买一个通用的power wrench. -indexguy- ♂ (0 bytes) () 09/09/2020 postreply 11:03:57
• 我是用打火 -chinomango- ♂ (0 bytes) () 09/28/2020 postreply 19:06:01
• 恳请来图片 -piper- ♀ (0 bytes) () 09/09/2020 postreply 07:53:51
• 油管有很多视频。 -indexguy- ♂ (0 bytes) () 09/09/2020 postreply 11:05:01
• 不会吧,这是要炸版的架势啊。 -biglow- ♂ (0 bytes) () 09/09/2020 postreply 07:52:46
• Why don’t you wrap him up? -MoonRiverMe- ♂ (0 bytes) () 09/09/2020 postreply 09:21:17
• 等他炸完了再卷。 -biglow- ♂ (0 bytes) () 09/09/2020 postreply 12:51:42
• 拆engine mount(dog bone). 后面的螺栓是痛点之二。 -indexguy- ♂ (182 bytes) () 09/09/2020 postreply 07:54:31
• 许多后续的chain引擎,水泵铝壳与引擎铝壳连接的10多颗螺丝,貌似没有铁螺栓与铝发生反应的问题。 -老金工- ♂ (0 bytes) () 09/09/2020 postreply 08:10:26
• 第二代sienna用两根长铁螺栓,穿过铝制X frame. 结果,螺栓生锈堵死缝细,润滑油过不去。 -indexguy- ♂ (44 bytes) () 09/09/2020 postreply 11:19:52
• 拆X frame support. 因为事先灌了不少润滑油,很容易拿下。 -indexguy- ♂ (0 bytes) () 09/09/2020 postreply 08:12:23
• 松开发电机螺栓,做好记号。松了22圈。卸下发电机皮带。 -indexguy- ♂ (0 bytes) () 09/09/2020 postreply 08:42:15
• 拧多少圈也要数?拧多紧按一下皮带不就知道了吗? -MoonRiverMe- ♂ (0 bytes) () 09/09/2020 postreply 09:19:56
• 卸下power steering pump 皮带。 -indexguy- ♂ (0 bytes) () 09/09/2020 postreply 08:50:28
• 用租来的pulley puller 卸下crankshaft pulley. 要自己买两个8mmx1.25 - 70mm的螺栓。 -indexguy- ♂ (0 bytes) () 09/09/2020 postreply 08:58:42
• 上个茅坑也要向全世界宣布每走一步迈出了左脚还是右脚? -MoonRiverMe- ♂ (0 bytes) () 09/09/2020 postreply 09:16:35
• 卸下连接发电机的bracket. 松开固定电缆的四个连接件。搞坏最后一个。 -indexguy- ♂ (50 bytes) () 09/09/2020 postreply 09:54:04
• 卸下底部防尘罩,四个m10螺栓。卸下顶部防尘罩,五个M10螺栓。 -indexguy- ♂ (0 bytes) () 09/09/2020 postreply 09:57:45
• 看到了正时皮带,16万迈后,完好如初。没有开裂。中盘休息。 -indexguy- ♂ (0 bytes) () 09/09/2020 postreply 10:24:12
• 见过不少换出的Toyota, Lexus 十几,二十万哩的timing belt,状况都还不错。水泵则差些。 -iGarage- ♂ (0 bytes) () 09/09/2020 postreply 11:03:11
• 16万迈换过火花塞,一点都没坏。纯属脱了裤子放屁。这次也是这个感觉。 -indexguy- ♂ (0 bytes) () 09/09/2020 postreply 11:12:35
• TimingBelt,10万Mi朝上就是anytime的事情,外观可能很好。 -老金工- ♂ (0 bytes) () 09/09/2020 postreply 13:56:16
• corolla有12万6断正时带的例子 -chinomango- ♂ (0 bytes) () 09/28/2020 postreply 19:08:51
• 继续。拆engine mount bottom base. 后面沉头的螺栓很难搞。 -indexguy- ♂ (122 bytes) () 09/09/2020 postreply 11:41:24
• Lug Nut拧花了 有什么办法卸下来吗 -落城一哥- ♂ (0 bytes) () 09/09/2020 postreply 12:29:43
• 用小半号的12角 socket 敲进去 -iGarage- ♂ (0 bytes) () 09/09/2020 postreply 12:40:36
• 多谢!去试试。还有人有别的法子么 -落城一哥- ♂ (0 bytes) () 09/09/2020 postreply 12:44:12
• 用impact wrench試試 -violinpiano- ♂ (0 bytes) () 09/09/2020 postreply 12:52:40
• 也想过去买这种电动的试试,但没有把握 -落城一哥- ♂ (0 bytes) () 09/09/2020 postreply 13:10:02
• 也想过让修车铺卸下来再换新的 -落城一哥- ♂ (0 bytes) () 09/09/2020 postreply 13:11:11
• 用bolt extractor -piper- ♀ (0 bytes) () 09/09/2020 postreply 13:13:31
• 6角的lug nuts怎么花法?来张图片看看。你的套筒不也是6 -piper- ♀ (0 bytes) () 09/09/2020 postreply 13:17:34
• 套筒打滑。手头无照 -落城一哥- ♂ (0 bytes) () 09/09/2020 postreply 13:22:28
• 你换用6边的套筒就行了 -piper- ♀ (0 bytes) () 09/09/2020 postreply 13:26:08
• 用的就是六边套筒。六角Nuts的角化了 -落城一哥- ♂ (0 bytes) () 09/09/2020 postreply 13:30:29
• 角花了,是因为你用了12边的套筒,换成6边的就行了 -piper- ♀ (0 bytes) () 09/09/2020 postreply 14:10:17
• 没有用过12边的。一直用六边的。可能是上的时候用劲过猛 -落城一哥- ♂ (0 bytes) () 09/09/2020 postreply 14:24:49
• 用6边的花了,这得花多大的力。你可以观察一下套筒里面的形状, -piper- ♀ (163 bytes) () 09/09/2020 postreply 15:27:15
• 这个不会错的 -落城一哥- ♂ (0 bytes) () 09/09/2020 postreply 15:33:53
• 六角花不罕见,Eric的视频里都可看见 -chinomango- ♂ (0 bytes) () 09/28/2020 postreply 19:11:31
• lug nut extractor -biglow- ♂ (0 bytes) () 09/09/2020 postreply 14:08:13
• 这是其中之一 -落城一哥- ♂ (143 bytes) () 09/09/2020 postreply 14:23:33
• 那个螺栓的净空很小,我怀疑bolt extractor 能否装的上。最重要的是用六边套筒,套筒完全套入,没有角度。 -indexguy- ♂ (0 bytes) () 09/09/2020 postreply 15:10:17
• bolt extractor 和套筒形状是一样的 -piper- ♀ (87 bytes) () 09/09/2020 postreply 15:29:36
• 看来要买一套。 -indexguy- ♂ (0 bytes) () 09/09/2020 postreply 17:42:59
• 正时皮带暴露后,顺时针转直到三个点全部对正。 -indexguy- ♂ (163 bytes) () 09/09/2020 postreply 13:40:21
• 手册说,这时应逆时针转大约60度。这一步争议很大。我转了。 -indexguy- ♂ (0 bytes) () 09/09/2020 postreply 13:42:49
• 拆tensioner 遭到麻烦,前面一个好拆。后面一个螺栓套不上套筒, -indexguy- ♂ (219 bytes) () 09/09/2020 postreply 13:51:26
• 拆正时皮带,idler. 下面那个要用10 mm hex bit socket. -indexguy- ♂ (0 bytes) () 09/09/2020 postreply 14:26:37
• 水泵上有两根螺栓,要用E-8套筒,网上多人拧断该螺栓。我不敢用力。 -indexguy- ♂ (0 bytes) () 09/09/2020 postreply 14:55:26
• 今天到此为止,谢谢大家围观。 -indexguy- ♂ (0 bytes) () 09/09/2020 postreply 14:56:33
• 谢天谢地 -MoonRiverMe- ♂ (0 bytes) () 09/09/2020 postreply 15:32:27
• 告你一个换timing belt的窍门 -MoonRiverMe- ♂ (346 bytes) () 09/09/2020 postreply 15:52:19