请教波大和有经验的地主:暖气炉达到设定温度后,有2-3次短暂重启的现象。正常吗?可能的修理思路?

本帖于 2024-02-08 23:36:50 时间, 由普通用户 yuanshangdu 编辑

现象:暖气炉在达到设定温度后停下来后一两分钟后,Blower会重新启动两三次,启动时间大约10-20秒,启动间隔大约一两分钟。启动时感觉好像炉子并没有点火或者燃烧。

已经采取的行动:

您的修暖气(1)和(2)都学习了。

温控器换过了。

Flame sensor也清洁了。

还是同样的现象。难道是炉子的自我保护机制?残留的热空气可能导致炉子自动排风?

录像:

录像1: 自动短暂重启 - 1. After reaching 67F (set 67F), the furnace restarted twice briefly and stoppped.MOV - Google Drive

录像2: 启动的全过程 - 2. Full ignite process Room 68F, Set 69F. Does this look normal.MOV - Google Drive

请教:

多次自动重启正常吗?如果不正常,可能的修理思路有哪些?本人理工男。

 

所有跟帖: 

Change control board. -smlandlord- 给 smlandlord 发送悄悄话 smlandlord 的博客首页 (0 bytes) () 02/09/2024 postreply 00:12:51

谢谢! -yuanshangdu- 给 yuanshangdu 发送悄悄话 yuanshangdu 的博客首页 (0 bytes) () 02/09/2024 postreply 05:56:10

you meant the inducer motor ran and stopped? what is -borisg- 给 borisg 发送悄悄话 borisg 的博客首页 (24 bytes) () 02/09/2024 postreply 01:51:22

No. The blower motor restarted briefly. -yuanshangdu- 给 yuanshangdu 发送悄悄话 yuanshangdu 的博客首页 (281 bytes) () 02/09/2024 postreply 06:08:33

you need to take out the cover to check -borisg- 给 borisg 发送悄悄话 borisg 的博客首页 (304 bytes) () 02/09/2024 postreply 08:04:58

Thanks for the feedback! -yuanshangdu- 给 yuanshangdu 发送悄悄话 yuanshangdu 的博客首页 (820 bytes) () 02/09/2024 postreply 10:13:20

This furnace's control board appears no indicator lights. -yuanshangdu- 给 yuanshangdu 发送悄悄话 yuanshangdu 的博客首页 (181 bytes) () 02/09/2024 postreply 06:40:06

把control board 拿下来,肉眼检查一下有没有烧黑的,接触不良的,如果有,重新焊一下,还不行就换新的 -andy99- 给 andy99 发送悄悄话 (0 bytes) () 02/09/2024 postreply 08:24:21

多谢反馈! -yuanshangdu- 给 yuanshangdu 发送悄悄话 yuanshangdu 的博客首页 (0 bytes) () 02/09/2024 postreply 10:03:02

请您先登陆,再发跟帖!