轿车前后轮之间高度不够,平时用的Rhino ramps插不进去,不能同时把前后轮开上去。我每次要先倒车把和前轮后轮开上一对矮点的home made wood ramps和正常高度的Rhino ramps, 然后再用Jack把前轮抬高换成后轮一样高度的Rhino ramps. 结束了再反过来,有点麻烦。谁有更好的妙招?好像有卖low profile car ramps的,价钱还不便宜。
你们修马车要钻车底时是怎么把车架高架平的?
所有跟帖:
• 4个jack stands?用过ramp,结果直接run over,哈哈 -langxing- ♂ (0 bytes) () 09/24/2022 postreply 10:31:44
• Jack stands 不如轮子着地安全 -DC_Jeeper- ♂ (216 bytes) () 09/24/2022 postreply 12:12:51
• 我有一对SUV/pickup用的铁架,小车用还得加垫2x10 - 其实该用2x12 -chinomango- ♂ (0 bytes) () 09/24/2022 postreply 12:56:17
• 俺是从中间顶起,3吨的floor jack可以顶起20多寸,底下干活基本够用。 -langxing- ♂ (123 bytes) () 09/24/2022 postreply 18:50:35
• 中间顶起是指一侧的中间,还是前后的中间? -DC_Jeeper- ♂ (123 bytes) () 09/25/2022 postreply 04:42:56
• 我说的是左右的中间,前面一个顶点,后面一个顶点。 -langxing- ♂ (228 bytes) () 09/25/2022 postreply 10:53:06
• 我第一次用ramp是在车库里,开过了,差点撞墙上去了 -ddy- ♂ (0 bytes) () 09/24/2022 postreply 14:03:56
• 哈哈哈,俺第一次也是over了,看样子众多Diyer都走过同一条路 -mountrobson- ♂ (0 bytes) () 09/25/2022 postreply 18:08:11
• 刚跑到Harbor Freight买了个这东西 -DC_Jeeper- ♂ (237 bytes) () 09/24/2022 postreply 12:08:21
• 我是先开到2x10上,不敢用塑料的不知何时老化 -chinomango- ♂ (0 bytes) () 09/24/2022 postreply 12:09:55
• 我倒是想问如何保证ramp不开过头? -chinomango- ♂ (0 bytes) () 09/24/2022 postreply 12:13:55
• 往上开时坡度比较大要加点油门 -DC_Jeeper- ♂ (114 bytes) () 09/24/2022 postreply 13:04:25
• 我是用上 parking brake, 再往上开。 -TheHawk- ♂ (0 bytes) () 09/24/2022 postreply 19:01:59
• 切勿这样操作。 -TBz- ♂ (349 bytes) () 09/24/2022 postreply 20:29:22
• 谢! -TheHawk- ♂ (0 bytes) () 09/25/2022 postreply 15:18:27
• Low profile ramps是用來加高車身後,方便油压Jac伸到車下,一般是跑車才用,升那点高度沒其它用處 -khyang86- ♂ (0 bytes) () 09/24/2022 postreply 12:51:46
• 这正是我的用意 -DC_Jeeper- ♂ (141 bytes) () 09/24/2022 postreply 13:08:51
• 结果如图 -DC_Jeeper- ♂ (82 bytes) () 09/24/2022 postreply 13:12:14
• RhinoGear?你不是开上去的 - 因为ramp是对立的? -chinomango- ♂ (0 bytes) () 09/24/2022 postreply 22:13:25
• 倒车上去,然后再抬车头把前面的矮ramp换成高的。方向相对,连wheel chocks都可以不用 -DC_Jeeper- ♂ (0 bytes) () 09/25/2022 postreply 04:28:56
• 干脆上auto lift. $3000 应该够了吧。省下人工买工具。 -PrimeryColor- ♀ (0 bytes) () 09/24/2022 postreply 15:02:32
• 没车库放 -DC_Jeeper- ♂ (0 bytes) () 09/24/2022 postreply 17:34:09
• 要干什么活?非把车子搞平? -langxing- ♂ (0 bytes) () 09/24/2022 postreply 15:09:45
• Transmission fluid, differential fluid,都需要放平.放机油最好也要放平 -DC_Jeeper- ♂ (0 bytes) () 09/24/2022 postreply 17:36:17
• 友情分享: 用RAMP 的时候,左脚准备在刹车上,右脚踩油门,才不容易过头。像正常开车那样,都是右脚,很容易过头。 -山寺桃花- ♂ (0 bytes) () 09/24/2022 postreply 18:01:57
• 另外四驱车用岩石模式,跟玩似的轻松上RAMP -山寺桃花- ♂ (0 bytes) () 09/24/2022 postreply 18:03:18
• 这是个好主意,我的crawl control function 还从来没用过 -DC_Jeeper- ♂ (0 bytes) () 09/25/2022 postreply 04:32:03
• Rhino ramps + 两Jack stands -iGarage- ♂ (0 bytes) () 09/24/2022 postreply 19:51:47
• 前面有童鞋可能担心这种有后溜,因为没有卡后轮 -soccer88- ♂ (0 bytes) () 09/24/2022 postreply 20:04:53
• 这担心是多余的,Ramp上面有平台。 Jack stand 不可能溜车,除非在坡面上 -iGarage- ♂ (0 bytes) () 09/24/2022 postreply 20:39:56
• 这个:Ramp在后轮,至少有Parking brake -soccer88- ♂ (194 bytes) () 09/24/2022 postreply 22:14:13
• Rhino ramps是空心的,安全没问题? -chinomango- ♂ (0 bytes) () 09/24/2022 postreply 22:22:23
• 放心,结实的很,十年以上不放心就换新的 -DC_Jeeper- ♂ (0 bytes) () 09/25/2022 postreply 04:35:05
• 这样不容易保持水平,两对一样高的ramps在平地上可以确定是水平的 -DC_Jeeper- ♂ (0 bytes) () 09/25/2022 postreply 09:58:35
• 平地有吗?通常要排水有斜度的 -chinomango- ♂ (0 bytes) () 09/25/2022 postreply 21:07:19
• 我用QuickJack 5000 便携式汽车举升系统4年多。安全,省事,方便。 -man008- ♂ (0 bytes) () 09/24/2022 postreply 23:08:17
• 想提这个,就是贵一点点 -soccer88- ♂ (0 bytes) () 09/25/2022 postreply 00:13:49
• 这个我也觉得危险,方形没有三角支撑 -chinomango- ♂ (0 bytes) () 09/25/2022 postreply 08:16:11
• 如果举起重量还不够令人信服,请观看此视频,了解 QuickJack 实际举起重量! -man008- ♂ (715 bytes) () 09/25/2022 postreply 12:50:42
• 直起没问题,如果刚好有剪切力或地震呢?没有利用三角形的稳定性 -chinomango- ♂ (0 bytes) () 09/25/2022 postreply 21:09:08
• 太占地方,有点笨重 -DC_Jeeper- ♂ (0 bytes) () 09/25/2022 postreply 09:56:39
• 我是把它放在车库门后面。 -man008- ♂ (81 bytes) () 09/25/2022 postreply 12:43:39
• 赞well organized -DC_Jeeper- ♂ (0 bytes) () 09/25/2022 postreply 15:05:51