我的MB CLK350前后轮看上去都是内八字,好像BMW也是设计成这样的,而且tire tread都是有方向的,后胎比前胎宽,所以前后左右都不能rotate.周末把轮胎卸下来看到磨损非常不均匀,内存快秃了外侧还剩很多,马上准备换了。我的问题是这样的磨损是设计上导致不可避免的单侧磨损,还是我需要做个Alignment了?我这次要选个没有方向的轮胎,至少左右可以过一段时间rotate一下。
Tire unevenly worn
所有跟帖:
• 前轮内八字是正常的, 不过需要做个Alignment。 -jason1020- ♂ (0 bytes) () 09/07/2021 postreply 13:27:11
• 这种spec估计dealer 比较清楚 -DC_Jeeper- ♂ (95 bytes) () 09/07/2021 postreply 17:32:13
• 这种磨损不正常。 -Oneshotkill- ♂ (0 bytes) () 09/07/2021 postreply 13:29:35
• 所以你也认为alignment有问题? -DC_Jeeper- ♂ (0 bytes) () 09/07/2021 postreply 17:33:45
• 如果没有改装过,应该去查查tire alignment,送两张BMW SAV后轮@30K公里的照片。 -Oneshotkill- ♂ (178 bytes) () 09/07/2021 postreply 18:25:54
• 你这个看上去磨损正常 -DC_Jeeper- ♂ (0 bytes) () 09/08/2021 postreply 03:14:45
• 前轮toe out 太多也会有这种轮胎磨损。所以还是得去检查alignment. -觅音- ♂ (0 bytes) () 09/08/2021 postreply 08:44:06
• 运动型车都是负camber,尤其是后轮,所以轮胎内侧先磨损 -jwhzzj- ♂ (0 bytes) () 09/07/2021 postreply 14:10:01
• 前后轮都是内侧磨损明显 -DC_Jeeper- ♂ (41 bytes) () 09/07/2021 postreply 17:35:17
• 你得看你的alignment specification -MoonRiverMe- ♂ (189 bytes) () 09/07/2021 postreply 14:12:47
• 没有查过spec -DC_Jeeper- ♂ (135 bytes) () 09/07/2021 postreply 17:28:06
• 您这是哪个位置的胎? 平时胎压维持正常吗? -总要注册- ♂ (0 bytes) () 09/07/2021 postreply 15:59:45
• 前胎,胎压一直保持厂家推荐的 -DC_Jeeper- ♂ (47 bytes) () 09/07/2021 postreply 17:29:26
• 那前后两侧胎的内边都有对等程度的磨损? 应该 -总要注册- ♂ (119 bytes) () 09/07/2021 postreply 17:58:59
• 对,两边磨损程度相同 -DC_Jeeper- ♂ (137 bytes) () 09/07/2021 postreply 18:15:19
• 你找到dealer的话, 他们应该知道原厂的spec, 不会乱来的。 -总要注册- ♂ (84 bytes) () 09/07/2021 postreply 19:52:38
• 你这staggered胎,肯定是运动配置,alignment指标可能与四方胎不一样,让dealer检查一下吧 -iGarage- ♂ (0 bytes) () 09/07/2021 postreply 17:54:44
• 我先online查一下厂家设置 -DC_Jeeper- ♂ (120 bytes) () 09/07/2021 postreply 18:21:44
• 前胎30psi的建议压力很有问题。换胎后你前后都打到36 continental 的胎号称8万英里,用8万公里应该没问题吧 -圆老扁- ♂ (0 bytes) () 09/07/2021 postreply 18:53:26
• 查了tire pressure spec -DC_Jeeper- ♂ (126 bytes) () 09/08/2021 postreply 03:23:27
• 说明你载重不够,空车内8字,载重后就是垂直的。下次装几百斤大米压车, 哈哈 -bushihandyman- ♂ (0 bytes) () 09/08/2021 postreply 07:01:24
• 哈哈,那是是外八字吧?内八字中间越重轮子应该越往内撇 -DC_Jeeper- ♂ (0 bytes) () 09/08/2021 postreply 10:33:22
• 他根本就没看懂你那原贴,要不就是连小学几何都没学会 -MoonRiverMe- ♂ (113 bytes) () 09/08/2021 postreply 11:38:15
• 看看这个坛子里还有比你更蠢的吗?哈哈 -bushihandyman- ♂ (0 bytes) () 09/08/2021 postreply 12:15:16
• Everyone knows how stupid you dickhead are -MoonRiverMe- ♂ (171 bytes) () 09/08/2021 postreply 13:05:55
• 不是开玩笑了,你是内8不够, 正常的都是内8一点点,有重量就垂直了, 不可能外8的 -bushihandyman- ♂ (0 bytes) () 09/08/2021 postreply 12:12:23
• 说说我的例子 -MoonRiverMe- ♂ (250 bytes) () 09/08/2021 postreply 16:48:57
• 谢谢,换胎时我会让他们仔细查一下 -DC_Jeeper- ♂ (0 bytes) () 09/08/2021 postreply 17:42:51
• 用手使劲压车头两角几下看得用多大劲儿才能压下去就知道了 -MoonRiverMe- ♂ (69 bytes) () 09/08/2021 postreply 19:41:41
• 试了悬挂很紧凑 -DC_Jeeper- ♂ (68 bytes) () 09/09/2021 postreply 04:17:47