motor mount螺栓卸不下来,请支招

本帖于 2019-04-13 21:03:14 时间, 由普通用户 chinomango 编辑

08 odyssey front engine mount,4x14mm标称力矩似乎是40ftlbs,卸下的两个螺栓外貌不一,怀疑有人动过。另两个呈对角,其一需用wobble externsion。用了WD40,DCF899号称1200ftlbs的Impact wrench,5AH新电池,卸不动也没滑丝。本打算卸掉后就顶起来变速箱的,现在车在ramp上。

上面的stop brakcet 2x17mm力矩58ftlbs,很容易就卸了,但下面没有橡胶套,似乎是动过。

补充:前mount被人换过,非原厂件,结果是两个40ftlbs的螺栓卸不下来,stop胶套没有,stop bracket上2x17mm是滑丝的,难怪轻轻一拧就下来了。

所有跟帖: 

火攻最有效。遇到过类似问题,一天都没下来,火炬五分钟搞定。 -yanif- 给 yanif 发送悄悄话 (0 bytes) () 04/13/2019 postreply 15:05:29

火只能由下面,是烧螺栓还是螺栓周围的铁件? -chinomango- 给 chinomango 发送悄悄话 chinomango 的博客首页 (0 bytes) () 04/13/2019 postreply 15:57:08

火炬喷灯任意方向都不受限制。螺栓螺母都烧。 -yanif- 给 yanif 发送悄悄话 (0 bytes) () 04/13/2019 postreply 16:30:31

请介绍一款喷灯,焊水管的行不行? -chinomango- 给 chinomango 发送悄悄话 chinomango 的博客首页 (0 bytes) () 04/13/2019 postreply 21:14:17

应该就是焊水管的blow torch。。。。 -偶尔疯癫- 给 偶尔疯癫 发送悄悄话 偶尔疯癫 的博客首页 (0 bytes) () 04/13/2019 postreply 23:24:33

有些焊水管的会有anti-tip switch.不能倒着拿,pencil torch 不受限制. 链接见内。 -yanif- 给 yanif 发送悄悄话 (452 bytes) () 04/14/2019 postreply 06:34:10

re这个。。。。。 -偶尔疯癫- 给 偶尔疯癫 发送悄悄话 偶尔疯癫 的博客首页 (0 bytes) () 04/13/2019 postreply 23:25:29

Bolt nut extractor + impact wrench 分分钟搞定 -bushihandyman- 给 bushihandyman 发送悄悄话 bushihandyman 的博客首页 (0 bytes) () 04/13/2019 postreply 17:06:59

Impact wrench用了1200ftlbs的DCF899居然没戏 -chinomango- 给 chinomango 发送悄悄话 chinomango 的博客首页 (0 bytes) () 04/13/2019 postreply 20:59:40

rear mount的17mm穿心螺栓也没卸下来,补充两照片 -chinomango- 给 chinomango 发送悄悄话 chinomango 的博客首页 (368 bytes) () 04/13/2019 postreply 21:01:16

后面这个看不出有裂缝,没必要更换吧。看到人家是2面同时施力,抵消塑料粘合在螺钉上的扭力损失。 -needtime- 给 needtime 发送悄悄话 needtime 的博客首页 (174 bytes) () 04/14/2019 postreply 06:39:22

看到的是橡胶垫片看不到里面,取下后里面破掉了 -chinomango- 给 chinomango 发送悄悄话 chinomango 的博客首页 (0 bytes) () 04/14/2019 postreply 13:50:33

上这个 -MoonRiverMe- 给 MoonRiverMe 发送悄悄话 (184 bytes) () 04/14/2019 postreply 08:25:13

未滑丝用不着extractor吧? -chinomango- 给 chinomango 发送悄悄话 chinomango 的博客首页 (0 bytes) () 05/09/2019 postreply 20:36:05

早就该上照片了 -MoonRiverMe- 给 MoonRiverMe 发送悄悄话 (0 bytes) () 04/14/2019 postreply 08:26:20

PB blaster -biglow- 给 biglow 发送悄悄话 biglow 的博客首页 (29 bytes) () 04/13/2019 postreply 21:21:04

14mm按理我把它拧滑丝都该下来的,也许新的DCF899或新电池有问题(过载保护)?不过我用的是3/8接长杆 -chinomango- 给 chinomango 发送悄悄话 chinomango 的博客首页 (0 bytes) () 04/13/2019 postreply 21:39:03

PB blaster泡一晚上。。。然后breaker bar手动试试?。。。。。 -偶尔疯癫- 给 偶尔疯癫 发送悄悄话 偶尔疯癫 的博客首页 (0 bytes) () 04/13/2019 postreply 23:23:44

今天换了两侧lower control arm/sway bar,只好等以后了 -chinomango- 给 chinomango 发送悄悄话 chinomango 的博客首页 (0 bytes) () 04/14/2019 postreply 14:10:14

有没有先吊起或撐起Motor,降低螺栓負荷? -khyang86- 给 khyang86 发送悄悄话 (0 bytes) () 04/14/2019 postreply 05:55:57

后面的有试了几种高度;前面的螺栓往下在frame上无负荷 -chinomango- 给 chinomango 发送悄悄话 chinomango 的博客首页 (0 bytes) () 04/14/2019 postreply 07:59:48

如果搞不定,去经常去的小车行,让人帮帮忙,给些小费 -soccer88- 给 soccer88 发送悄悄话 soccer88 的博客首页 (0 bytes) () 04/14/2019 postreply 15:36:01

正解。DIY 要以低成本快速解决问题为原则。 -RoseBuilder- 给 RoseBuilder 发送悄悄话 (251 bytes) () 04/15/2019 postreply 13:20:50

花2百5换了后面的-没力臂使不上劲,前面的自己换的 -chinomango- 给 chinomango 发送悄悄话 chinomango 的博客首页 (0 bytes) () 05/09/2019 postreply 20:37:20

请您先登陆,再发跟帖!