请教: 如何卸锈了的车轮?
所有跟帖:
•
有没有铁头靴子?有的话,穿那鞋子往轮胎下侧踢
-abita-
♂
(0 bytes)
()
12/03/2009 postreply
14:51:05
•
在轮胎架空后踢
-abita-
♂
(0 bytes)
()
12/03/2009 postreply
14:51:52
•
当然螺帽先卸下
-说白了-
♂
(0 bytes)
()
12/03/2009 postreply
15:15:48
•
多谢,我去试试.
-bestbuy2-
♀
(0 bytes)
()
12/03/2009 postreply
15:50:15
•
怎么危险了?怎么就转不了90度?你自己试过?
-说白了-
♂
(0 bytes)
()
12/03/2009 postreply
16:13:47
•
if the wheel suddenly drop out that might cause the bolt on hub
-fixanycars-
♀
(197 bytes)
()
12/03/2009 postreply
18:48:50
•
Use common sense. You get control by lowering the Jack slowly
-说白了-
♂
(395 bytes)
()
12/03/2009 postreply
19:11:19
•
many diyers kill themselves accidentally.
-fixanycars-
♀
(0 bytes)
()
12/04/2009 postreply
15:31:16
•
if your car has ABS, it is better to let shop to do the work
-fixanycars-
♀
(176 bytes)
()
12/04/2009 postreply
15:39:02
•
拉手刹,同时后轮用东西顶住,用common sense确认安全
-说白了-
♂
(46 bytes)
()
12/03/2009 postreply
17:57:55
•
多谢,只能明天去试试,现在太晚了。
-bestbuy2-
♀
(0 bytes)
()
12/03/2009 postreply
18:01:26
•
用锤子敲,要振动不要晃动
-狼主-
♀
(0 bytes)
()
12/04/2009 postreply
06:32:25
•
要是敲不下来,轱辘转个也未必行。锤子敲是小学难度
-狼主-
♀
(30 bytes)
()
12/04/2009 postreply
06:36:59
•
用锤子敲了15分钟,尽没敲下来。
-bestbuy2-
♀
(150 bytes)
()
12/04/2009 postreply
11:10:36
•
一年绝对锈不了这样!啥车这么矫情?
-狼主-
♀
(0 bytes)
()
12/04/2009 postreply
13:38:36
•
2001 Toyota Camera LE, 两个前轮都这样,不知怎么搞的。
-bestbuy2-
♀
(0 bytes)
()
12/04/2009 postreply
14:53:22
•
啊,是Toyota Camera。再一次验证了一个传说...
-TBz-
♂
(0 bytes)
()
12/04/2009 postreply
22:41:54
•
卖得好是因为粉丝多..
-北航新保理英子-
♀
(0 bytes)
()
12/05/2009 postreply
07:09:07
•
先用wd-40...
-喜欢豪宅-
♂
(0 bytes)
()
12/04/2009 postreply
11:06:15
•
WD-40 是不是除锈的?在那能买到?对车轮及车轴会否有影响?
-bestbuy2-
♀
(69 bytes)
()
12/04/2009 postreply
11:13:25
•
伙计,要是你不知道WD-40,这活你干不了
-狼主-
♀
(0 bytes)
()
12/04/2009 postreply
13:53:30
•
有可能干不了,但先学一下。在Autozone 找到了WD-40
-bestbuy2-
♀
(0 bytes)
()
12/04/2009 postreply
14:47:41
•
别喷多了,祝你好运
-狼主-
♀
(0 bytes)
()
12/04/2009 postreply
17:15:52
•
你卸了几颗螺钉?
-three-
♂
(0 bytes)
()
12/04/2009 postreply
17:34:53
•
5颗螺钉
-bestbuy2-
♀
(0 bytes)
()
12/04/2009 postreply
18:44:44
•
三招两试
-three-
♂
(194 bytes)
()
12/04/2009 postreply
18:36:17
•
多谢多谢,先试你的方案1和2。若不行执行方案3.
-bestbuy2-
♀
(0 bytes)
()
12/04/2009 postreply
18:43:31
•
试2时注意安全,螺钉松紧适中,不可过松,会伤刹车盘
-three-
♂
(0 bytes)
()
12/04/2009 postreply
20:52:06
•
千万注意!!!
-TBz-
♂
(54 bytes)
()
12/04/2009 postreply
22:46:25
•
见的多了,有的得上大锤子(HOIST 上安全)
-北航新保理英子-
♀
(0 bytes)
()
12/05/2009 postreply
07:11:16
•
车轮卸下来了,按three老大的方案2做的,多谢各位高手相助。
-bestbuy2-
♀
(101 bytes)
()
12/05/2009 postreply
09:19:44
•
很高兴能帮你解决问题, happy DIY
-three-
♂
(0 bytes)
()
12/05/2009 postreply
18:03:55