想更换这个2个MIC IC,可是不知道怎么下手?
一般的电烙铁根本无法操作,用HEAT GUN又怕伤了周围的原件。
谢谢!!!
各位大虾,帮俺看看,该怎么下手?真叫人有点抓狂!
所有跟帖:
• 用细铜丝线垫在烙铁下面加热,铜丝会吸收焊锡 -滋鄂- ♂ (0 bytes) () 12/10/2014 postreply 20:23:15
• 弄个吸锡器好像不是什么大不了的事情吧? -biglow- ♂ (0 bytes) () 12/10/2014 postreply 20:26:00
• 没玩过吧?取下有专用头,焊上用扁头就行了(见内)。油管上也有 -味苦- ♂ (138 bytes) () 12/10/2014 postreply 21:18:37
• 用锡纸剪个洞,露出要拆的芯片,其他用锡纸包严了。然后用heatgun吹两三分钟就下来了。 -追风大老虎- ♀ (0 bytes) () 12/10/2014 postreply 21:37:55
• 专业地是用棕色的耐热透明胶带粘盖周边元件,锡纸面大了会散热多 -obamacome- ♀ (0 bytes) () 12/12/2014 postreply 20:00:23
• google solder wick -lovecorn- ♂ (0 bytes) () 12/10/2014 postreply 21:38:50
• even easier, cut it. -lovecorn- ♂ (14 bytes) () 12/10/2014 postreply 21:40:08
• you may damage the solder pad -US_CAR.- ♂ (0 bytes) () 12/10/2014 postreply 22:10:56
• 这个问题我可以回答: -US_CAR.- ♂ (1466 bytes) () 12/10/2014 postreply 22:10:05
• 茅台也行,呵呵, 周末喝酒啦。 -墨西哥- ♂ (0 bytes) () 12/12/2014 postreply 09:29:30
• 以前没有专用工具时,都是用cutter把IC夹碎。如果不敢来硬的,可用大量的焊锡当导热体,先把一边焊开(IC下用刀片顶一下),然 -coolwin- ♀ (0 bytes) () 12/10/2014 postreply 23:02:23
• 直插式的穿孔元件可以这样做,但表面贴元件一夹就把PCB上的焊盘弄坏了,不能这么蛮干。 -US_CAR.- ♂ (0 bytes) () 12/10/2014 postreply 23:33:53
• 先示范方法2: 焊锡群殴。 -coolwin- ♀ (1316 bytes) () 12/12/2014 postreply 18:20:59
• 当然用蛮力的用力太小,方向和从什么地方开刀,得干废N块板子才能悟出来。但上面这方法无论生手熟手,基本上都能成功。 -coolwin- ♀ (0 bytes) () 12/12/2014 postreply 18:34:33
• 用与芯片排脚等宽的厚紫铜皮卷在烙铁上,自制个扁平头,瓦数及烙铁头太小不行 -obamacome- ♀ (79 bytes) () 12/12/2014 postreply 19:30:45
• 谢谢楼上的各位大虾。solution找到,报告一蛤。。。 -我爱北京大前门- ♂ (158 bytes) () 12/11/2014 postreply 08:34:08
• 这个要出事的。质量太差 -味苦- ♂ (0 bytes) () 12/11/2014 postreply 16:07:20
• 按滋鄂的做,Fry's有吸锡 的铜编织带。 -chinomango- ♂ (0 bytes) () 12/11/2014 postreply 08:48:45
• 若heatgun出风口太大,用罐头盒铁皮弯个遮风嘴套住吹,取下贴上芯片都能用,视频上的风口太小 -obamacome- ♀ (0 bytes) () 12/12/2014 postreply 19:21:01
• 这个专业一些,需要rework gun+rework tape.我这里是技术员做这个事。 -soccer88- ♂ (116 bytes) () 12/14/2014 postreply 03:48:11
• 我工作这里天天有这个活,嘿嘿 -soccer88- ♂ (0 bytes) () 12/14/2014 postreply 03:49:27
• 这有pin的好弄,滋鄂 说的对啊。 或用尖头的罗铁 一个一个pin 加热 翘起 -130131- ♂ (0 bytes) () 12/15/2014 postreply 09:36:35
• 我也做过这活儿。 -130131- ♂ (0 bytes) () 12/15/2014 postreply 09:37:15