给家里一个卫生间装costco买的bidet seat, 不巧的是配的T-Valve转到还没到完全彻底锁紧就碰墙了,导致有轻微漏水,这个有什么好办法么?(这个用上了自带的 3/8" spare nut,里面是个小塑料环)
给家里一个卫生间装costco买的bidet seat, 不巧的是配的T-Valve转到还没到完全彻底锁紧就碰墙了,导致有轻微漏水,这个有什么好办法么?(这个用上了自带的 3/8" spare nut,里面是个小塑料环)
• spare nut改软管 -chinomango- ♂ (0 bytes) () 02/17/2019 postreply 16:20:42
• 多谢老兄建议,立刻去了Ace hardware -jasonshane- ♂ (331 bytes) () 02/17/2019 postreply 18:12:16
• 螺纹上绕5圈teflon tape后再试试。 -易木- ♂ (0 bytes) () 02/17/2019 postreply 18:28:52
• 还是不行 -jasonshane- ♂ (498 bytes) () 02/17/2019 postreply 19:29:57
• 这里的问题是, 不能用npt, which is taper pipe thread. You want straight pi -PrimeryColor- ♀ (0 bytes) () 02/18/2019 postreply 09:41:26
• ??? -jasonshane- ♂ (130 bytes) () 02/18/2019 postreply 17:07:55
• There are 2 pipe threads, taper and straight, 铜接头是前者npt, 3通是后者n -PrimeryColor- ♀ (209 bytes) () 02/18/2019 postreply 18:34:46
• 多谢指教 -jasonshane- ♂ (50 bytes) () 02/18/2019 postreply 21:31:32
• 方案2 -PrimeryColor- ♀ (522 bytes) () 02/18/2019 postreply 07:52:04
• 还真有这种规格的 -jasonshane- ♂ (68 bytes) () 02/18/2019 postreply 08:48:22
• 几块钱是事,不懂为什么不换掉? -味苦- ♂ (0 bytes) () 02/17/2019 postreply 19:50:27
• 换 T-valve? -jasonshane- ♂ (965 bytes) () 02/17/2019 postreply 20:01:53
• No. 马桶是1/2" male, connect to female 1/2" on the T, then the ma -PrimeryColor- ♀ (158 bytes) () 02/17/2019 postreply 20:23:10
• 是想看有没有Tee的一头是可以直接到3/8 compression shutoff valve 上的 -jasonshane- ♂ (515 bytes) () 02/17/2019 postreply 20:35:33
• 和shut off valve 的接头形式没有一点关系。 -PrimeryColor- ♀ (0 bytes) () 02/17/2019 postreply 20:39:09
• 说明书的接法不可取。除非你要找麻烦。 -PrimeryColor- ♀ (0 bytes) () 02/17/2019 postreply 20:41:22
• 我理解你的意思是将T 头接到tank 的下面的出口那里 -jasonshane- ♂ (155 bytes) () 02/17/2019 postreply 21:34:17
• Sorry, 是7/8, 不是1/2. -PrimeryColor- ♀ (0 bytes) () 02/17/2019 postreply 21:53:35
• 3通直接装在马桶下面1/2"节头上, 再接软管。 -PrimeryColor- ♀ (0 bytes) () 02/17/2019 postreply 20:09:05
• 这个牌子的bidet是有接到tank下面的,但这个model不是 -jasonshane- ♂ (87 bytes) () 02/17/2019 postreply 21:20:17
• 还真不知道这个。 问题是有区别吗? 也许是防止水锤方面。 -PrimeryColor- ♀ (0 bytes) () 02/17/2019 postreply 22:00:41
• 应当是7/8". 不是1/2". -PrimeryColor- ♀ (0 bytes) () 02/17/2019 postreply 21:54:52
• 一般二个连接处螺纹要放纱布状的TAPE;才能不leak -财富001- ♂ (239 bytes) () 02/18/2019 postreply 07:07:55
• 方案1 -PrimeryColor- ♀ (316 bytes) () 02/18/2019 postreply 07:30:18
• 这个好! -jasonshane- ♂ (26 bytes) () 02/18/2019 postreply 08:47:09
• T接头上的螺帽和接头本身不是分离的吗?紧的时候拧螺帽,T的出口应该可以朝任何方向 -股市猎人- ♂ (0 bytes) () 02/18/2019 postreply 09:55:25
• 方案3, 这个应当是可以转动的。 -PrimeryColor- ♀ (168 bytes) () 02/18/2019 postreply 10:31:13
• 应该都是可以转动的,包括楼主买的bidet带的那个。 -股市猎人- ♂ (189 bytes) () 02/18/2019 postreply 11:47:52